Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I have a unterminated battery I'd like to terminate and plug into P3 with the appropriate matching size and I can't seem to find an indication of what I should use. What is...
Hi,
I'm using nRF52840 - QIAAD0 (it's revision 2 I think) and nrfx_saadc API v2 (but I don't think it doesn't really matter here)
tl;dr As stated in SAADC peripheral documentation...
Hello, i did my own custom board with a nrf52805 and I'm trying to put a module with different frames and when I do that my app is disconnecting 5seconds after. I didn't have...
Hello all,
I`m trying to use k_poll, it`s working okay, I just have an hard fauld error that drives me crazy, I have in main an loop which listen to k_pool_signals, the...
Hi,
Why I use the function m_device_state_set(cons, PM_DEVICE_STATE_SUSPENDED); to close the serial port is still a large current:38.80uA?
The verification method is as...
Hi there
I wrote SDK 17.2 ble_app_hrs to the module.
When connecting to an Android device, Empty PDUs will no longer be sent. I checked the RTC COUNTER, but it is incremented...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
We are in the process of adding FOTA to our custom project and...
We are using nRF52833 with DFU secure bootloader and implemented DFU master/host on ESP32 BLE. We observe that DFU bootloader get stuck in above locations in softdevice more...
Hi Nordic
I have been using your example on USB MST to embed it into my application
Everything works ok, but in the main loop im constantly polling for USB power event...
I'm looking at the nRF Connect SDK Matter documentation, and the intro page states :
"If you are new to Matter, check also the tutorials on DevZone ."
The link in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
