I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi All,
In my application I have two analog inputs coming from two different sources that I have to sample using one SAADC present inside NRF52. As far as I know, NRF52...
Hi,
I'm using nRF5 SDK V12.0, I found a strange problem. That is the UART can send data to PC, but it cann't receive data from PC. However, this problem just arise on some...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
hi
i am using nrf51822. i used the radio tranceiver example and it works well. I am planning to advertise the received packets so that the range can also be increased and...
Hi all --
I have a tricky layout "issue" where unfortunately, I've ended up connecting my I2C device to the BlueTooth module on the side of the module where my VDD isn...
I'm reading the SDK 10's GPIOTE doc and I'm wondering if there is a way to read a GPIO state without generating an event, ie, something like foo = PORTx.pin10 or alike.
...
Hi,
I have a central that is trying to pair with a peripheral. I want this connection to be secure and I want to use ECB for encryption of data. My peripheral does not have...
Hi,
I'm trying to communicate the nrf52832 with a LIS2DH accelerometer and when I'm trying to read 192 (32*6) bytes of data (to empty the entire accelerometer's FIFO) my...
Hi,
I want to know what is my execution time for each function.
I am using nrf51822 chip and the IDE is IAR Embedded Workbench.
How can i calculate the execution time...
