Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
hi
this is my timers_init(); func
static void timers_init(void)
{
uint32_t err_code;
// Initialize timer module.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS...
I am writing an App for the Central/Master side using the s130 v1.0.0 SD. I am connecting to the soft device using the python wrappers for the nRF51-BLE-Driver-Win 0.5.0....
I want to write a program in Keil by SPP for communicating with a thermal printer that uses SPP
but I can't find source code about that.
Is this possible to do this with...
Hello
i have nrf52 PAC10036 dev Board.
i am using the visualgdb.
when i try to create the instance of the TWI.
i got the error
please check image for detail.
How i can...
I want to turn off BLE-peripheral Advertising for 8 hours but I want to use another timer with period of 50ms to scan GPIO ,
when I change prescale of
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
Hello,
I am using nrf51822 doing projects. I met an issuse which is that at the first 6 minutes, it can normaly go into UART interrupt and run subroutine successfully....
I'm testing out TWI on pins 24/25 and I get a crash when I attempt to do a TWI transfer and I find myself in: WDT_IRQHandler ()
I'm using much of the example code:
APP_TWI_INIT...
Hello, I have a few nRF devices, and I am unsure as to which revision the ICs are. Here are the three HWIDs:
0x00AE,
0x0086, and
0x0077
I tried looking into the nRF51_Series_Compatibility_Matrix_v2...
Hi,
I need to sample 2 inputs at 200Hz and send it on an app. Can I send the data at this speed using UART service? I was trying to do it using HRM example but could not...
Hi, I am trying to compile the code
github.com/.../main.c.
I need to include the header file uart_confg.h, can someone tell me where I can find it in the sdk 10 component...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
