I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
Hi,
I use sd_ble_gattc_write function to write to my peripheral with my central device. I'm sure the settings should be right but i still can't see any change on peripheral...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
Hello All,
I am working with a pre-programed PCB; the main components of the are a nRF51822 chip, a GPS, and a GSM. I am using a J-link to communicate to the entire board...
Hi,
I have a BLE thermometer I want to snif using nRF-Sniffer and Wireshark.
Unfortunately I'm unable to sniff the data, I only see the initial "hand-shake".
Process...
Hello,
I have the nRF51822 evaluation kit, the Keil MDK software and a custom board with the nRF51822 microcontroller on it. My question is if it is possible to use the on...
Hi I am not sure on the nRF51422 chip the iBeacon function is fully supported, is it ?
I can make the examples working on it but on the Nordic site only on the nRF51822 chip...
