We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, I am trying a simple btle application where one mcu will send a "help" message and another will respond with its address. The mcu that asks for stores the address of...
Hello,
I would like to implement the nordic DFU protocol natively in a new app as I have historically found it tiresome and buggy to turn the DFU program into a library...
Hello, I am using eclipse app development, to achieve OTA function, use Maven to download DFU library, can not find the library, see your introduction： compile'no.nordicsemi...
I have a BLE circuit utilizing an NRF52832 cpu/integrated radio, necessary impedance matching network and a single ended micro-strip "L" antenna. How can I determine the gain...
I an trying to wake the chip and record the temperature readings when temperature reaches a certain threshold (eg: 80 deg C), can this be achieved using built-in temperature...
I debug the DFU Bootloader through UART,I am sure the APP code is complete updated,but the application does not run when the device is after bootloader to auto soft reset...
Hello:
I'm trying to get an example program ble_app_hrs running on my custom board, because earlier last month I couldn't write the cccd descriptor properly and I suspect...
i try to connect and read and write on my device with ionic2 BLE plugin , i can connect and also write on the device but when i try to read a data from device and use startNotification...
Dear team,
Our customer using "nRF51422 Development KiT8PCA10028)" with "ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex".
They can check advertising packets, but, they...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
hii team,
iam trying to pair my central app with one peripheral device which is generating random passkey while pairing .when central (my App) is sending pairing request...
Hi,
I am using the pin change interrupt example provided in the SDK examples. By setting the input sense to NRF_GPIOTE_POLARITY_LOTOHI, the interrupt handler is called...
Hello, i am a beginner, i have a doubt that my UART project is building without the softdevice being flashed and the output is not seen on the pins. I wanted to configure...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
