Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
The nRF52840 UART example uses pins 1.13 and 1.14 for the TX and RX pins on the Dev Kit (uart_pca10056) and has a default baud rate of 115200, but the 1.13 and 1.14 pins are...
Hi! I'm having issues with inconsistent battery readout results. I'll elaborate more below, but in general, I have multiple devices which 'sleep' most of the time, and when...
I have an issue when i am doing writing of a structure where autoprog is a struct like this :
typedef struct { uint8_t tag_tab[TAG_ID_LENGTH]; }tag;
typedef struct { uint8_t...
Installed nRFgo Studio lastest win64 verion nrfgostudiowin641212installer.msi and lastest windows 64 nRF-Command-Line-Tools_10_9_0_Installer_64.exe . But nRFgo does not work...
Hi!
I want to develop a simple program which count pulses in a digital pin in an interval of 10ms. I want to use a timer as a counter to count the pulses, also I want...
Hello Nordic Team,
We just received and test a new batch of SIMs using a nordic nRF9160. However, there is an error that doesn't allow to register these new SIMs. From LTE...
Hello,
we have a project on:
Periperal: experimental ble_app_blinky / and
Central: experimental ble_app_blinky c
We have add suplementary:
LEDBUTTON_LED4 ( BSP_BOARD_LED_3...
Hi,
I am unable to test current time service example.I followed all the steps mentioned to test CTS Example.But, below are the log messages:
Again if I try to reset...
I have an issue with my nrf9160 custom board.
I flashed successfully only 3 of 30 pieces batch. Other boards fail with "Failed to connect to target. No idcode detected"...
Hi !
I am working on aws_fota, with a nrf9160 dk, sdk 1.3.0. When I try to connect in mqtt, I get my IPv4 address I get the following message: ERROR - mqtt_connect...
Hello,
I'm trying to interface msp430fr5994 to nrf51822 as spi slave with soft device 110 and SDK v10. The master (msp40) sends 20 bytes to the slave (nrf51). The issue...
Hi,
I started debugging a device with an nRF52820 chip and found that the pinout is similar to nRF52833.
The test application was switching pin P0.15, but the ripple...
I'd like to order a debug in/out cable for the debugger (P18 & P19) on DK.
But I don't know what is the cable or the compatible sockets.
please let us know what is the...