i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...
Hello!
I'm trying to use the ram_retention in sdk 15 alpha to retain RAM in system off mode and do some power profiling.
The default code seems to retain 8 kB of RAM...
My project needs to use 2 different TWI instances and 1 SPI instance. I knew that it is not possible to use three instances at the same time in nRF52.
To implement 2 TWI...
Hi Nordic,
I am trying to enable the DC/DC converter on a PCA20006 rev 1.3.0.
I am using the softDevice S130.
1. Using the sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi.
I am using saadc example code or SDK V13 with the following requirements:
Voltage input up to 70mV,
Resolution: 50uV
So I did some modification to support...
Hello,
yesterday I got a Thingy:52 device at an event held in Frankfurt/Germany. At home I've tested the DFU for the latest firmware and observed that the image was transfered...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
To enable comparability with an existing client, I'm attempting to configure the nRF51822 to provide a GAP service that includes user description descriptors (UUID 0x2901...
