But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I see that there is a 1.2 Volt VBG reference available for the ADC but that reference doesn't seem to be available for the low power comparator. Is there any undocumented...
I'm developing a central providing NUS client services to multiple concurrent peripherals. I had code working reliably under SDK 9.0.0 based on the NUS client example in github...
Hi, we looked at your BOM for matching components in your file:
www.nordicsemi.com/.../15787782
for QFAC variant of the IC. You use LQP15MN27NG02D as 27nH inductor which...
Hello guys,
I am using this repo to update my device's firmware but after the update is complete, the iPhone cannot find the correct devices services anymore.
To detail...
We're using the NRF51822 and the S130 with V9.0 SDK, and we're using most of the features of the SDK for our Firmware; but I'm running into a problem flashing the device on...
I'm rolling my own very simple PWM implementation (I'm not using the PWM example code). My code is below:
#define GPIOTE_CHANNEL_NUMBER 0
#define PCLK16M 16000000
#define...
HI:
I use gzell protocol to realize 2.4G communication with SDK 5. I wonder that is the gazell protocol update in SDK9 or SDK10 ? and is there any improvement in latest version...
Hello:
I want use nrf51822's time/ppi/gpiote to capture the pwm rising/falling range duty.I want to know the most numbers of pwm channels duty parameters it can capture?...
Hi everybody,
as Nordic is currently working on this "Internet of things" thing and there are plans for an IPv6 over Bluetooth stack, I was wondering if it wouldn't be...
Is there a calling context restriction for sd_ble_gap_connect()? Either in the function call or where the peer address pointer is in memory?
I based my Central project...
Hi everyone,
I tried to test nRF51-ble-app-uart-static-passkey to learn the static passkey method.
I used PCA10001 EK board, with S110_7.1.0 and SDK_6.1.0.
Well, if I connect...
The maximum data length of a characteristic is 9, and I use the follow function to send the notification to a client
uint32_t dxs_send(dr_ble_dxs_t * p_dxs, uint8_t * p_data...
Hello,
I am debugging through UART with nrf52 and s132 softdevice using Keil V5 for the proximity app. When I flash the example app from the 9.2 SDK and look at the debug...
Is there a migration guide for the SDK 10 somewhere? I think the use of the APP_TIMER_DEF() macro is one thing that should be in it. Took me a while to understand why the...
