But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Issue is similar to
devzone.nordicsemi.com/.../
I'm developing an application based on latest SoftDevice 130_1.0.0 and using two or more DevKits.
My application starts...
Hi. My app based on S130_1.0.0 and is run on DevKit with 51422 chip. App advertises and scans at the same time with next params:
adv interval = 20mS;
scan...
im using nrf51822. before entering DFU mode I want to save data in flash. but when I call pstorage within reset_prepare function, it doesn't jump to DFU mode !!!!
reset_prepare...
Hello guys, i'm new in nRF51 DK board, and i would like to flash the .hex file to my board, but when i do it the board automatically unmounting himself and reset with the...
hello there i want to send negative acknowledgement then what should i do?? like i want to send some data and then i want to send negative acknowledgement
i am trying to use yggdrasil for nrf51422 (pca10028) with sdk 10.0. after installing, i cannot see the com port. How do I flash "connectivity_115k2_with_s130_1.0.0.hex" with...
Hi everyone!. I am beginner for Nordic Devices
I want to use RTC Clock with softdevices
so I loaded the project ble_uart_s130 from examples.
and I changed code like...
I have a ble central device. Sending commands to UART in main() works well. Sending in on_ble_evt() doesn't work (only the first char).
But I see in your examples that you...
Hi guys,
I've almost got DFU working on SDK10. However I am having issues at post validation of the image, specifically in the function dfu_init_postvalidate() in file...
Hello all,
Thank you in advance for taking your time for reading this question. I'm developing a proximity application and I have programmed the nRF51 DK with the s110...
Hi,
I am trying to set up a small mesh network. Basically I have a couple of PCA10028 (v1.1.0) and I have flashed the mesh example:
github.com/.../BLE_Gateway
One...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
