Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello.
I use SDK 8.0.0 and PCA10028 board. I try connect board to the Windows 8.1 PC ( i have Tablet PC and Desktop PC with BLE dongle). For connect board to Windows i...
I think I understand what these two flags do, the SYS one returns the system attributes, which I assume means data representing the CCCD for the service changed characteristic...
Hello,
Is there any compatible arduino lcd with existing library for the nRF51 Chipset?
So I can just plug it on the nRF51-DK, include the library and "lcd_wirte("text...
Dear Developers!
I'm a newbie in nrf51822
My Project needs to change between central and peripheral role. How can I apply OTA DFU with S130 soft device ?. In nrf51822 DFU...
Hi,
I used PPI module and Timer2 to generate a 4Mhz pwm. But I founld when using softdevice(s110 v7.0), the pwm will be broke a while by BLE advertising or connecting event...
What's wrong?
Device is connected. (nRF51822 Board - J Link - PC)
I downloaded a sample project, and when I open with Keil, then it shows following message.
What...
Hi all,
I would like to know which is the most recent SD and SDK that I should be using with my REV2 chips. In the compatibility matrix, there is no info about the SDK...
I am working on s120(central) and s130(central/peripheral). I am getting
BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST event after updating conn_parameters w.r.t to peer using sd_ble_gap_conn_param_update...
Using nRF51x and S110 v8 in a BLE application I want to generate a random 32 bit identifier and store at end of UICR on first power up only after factory flash (no erase needed...
The pwm library seems to add 10KB worth of code to my program. Alot of it probably comes from the nrf_drivers that are used, but still 10KB. While enabled it seems to pull...
Hello,
Since 2 weeks, I use heavily my nRF51-DK (PCA10028), with mbed compiler to make a BLE enabled device.
But, since few days, when i have tried to cut the SB9 in order...
I have a Rev3 nRF51822 chip (CFACA00) on a custom board (no external pull resistors on SWDIO or SWCLK), and I am using nRFgo Studio 1.20.0.2 to program SD 8.0.0 and my Nordic...
