Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
Can anyone tell me which example in SDK to use to send data(a simple text message) from nRF52832 board to an Android Phone. I have nRF Connect and nRF Tools applications...
HI,
I've noticed a few issues with the example app_level.c.
1: The g_set_transition() was updated in the 3.0.0 release to avoid a division by zero, however, this fix...
Hello all,
I recently migrated from SDK 15.0.0 to SDK 15.3.0 and as a result tried to migrate from SD 6.0.0 to 6.1.1.
My application goes to sleep after a while and when...
I am new to this environment.
Attempting to create a simple BLE app similar to the built-in BLE, but with some buttons to send predetermined commands to devices. Using the...
I applied Bonding to the UART example(ble_app_uart).
Bonding combined with the UART example works well, but there is one problem.
1. I did Bonding first. 2. After that...
Basically I get an Attribute not found error from sd_ble_gatts_value_get() in the nus_ble.c and then I never get any NUS events in the application. I'm trying to figure out...
Hi!
We have working solution with custom rf protocol based on NRF52832 and NRF52840(now it use 2 Mbps Nordic proprietary mode). Now we want improve it.
Could You give...
HI,
I have found some problem with nrfutil (version 5.2.0 installed from pypi).
Problem description:
When I am updating dfu with success (correct keys, packages etc...
Greetings,
I'm using 3 NRF52832 boards, s132 and SDK 14.2.0. I'm interested in connecting two hrs peripherals to a single hrs central, but have found some posts that say...
When creating an attribute specifying vloc as BLE_GATTS_VLOC_USER, it is not very clear that a storage pointer must be provided on creation of the attribute and cannot be...
Hi,e verybod, I use nrf51822 to do bluetooth keyboard, I hope the function is: After bluetooth keyboard connect the host,how to determine whether the connection is window...
I'm trying to create a virtual beacon on an Android Phone using nRF connect V4.22.3. Android Version on the phone is 8.1.0.
I've enabled a beacon using Advertiser. However...
In an BLE example I have a characteristic with the value 0x00001234. In the nRF Connect 2.0 for iOS i see the value 0x00001234 and in nRF Connect for Desktop v3.1 i see "34...
Using the logging module in ncs v1.0.0, I see some extra characters after the timestamp " <0x1b>[0m<inf>" and at the end of the line ", is there a way to fix this?
The terminal...
