Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
Traceback (most recent call last):
File "__main__.py", line 303, in <module...
Hi,
I have tried buttonless DFU in SDK 12, for which I have a few questions
(1) Is bootloader not needed if I use Buttonless DFU Template Application? However, SoftDevice...
I work with gcc on nordic nrf52 SDK13.0.0.
I see the post:
devzone.nordicsemi.com/.../
But if I try to change the packet in the radio_event_handler in active state,...
Hi I am trying to develop a an application to send data packets over ble using nordic uart service. I wanted to know what is the maximum bytes of data that I can send in one...
Hi,
I'm trying to integrate Bluetooth pairing code from experimental_ble_app_hrs_nfc_pairing example into ble_app_uart example (I have a project based on this example,...
Dear Nordic Team,
I want to know if we can support the real time talking like phone call between peripheral and central by software device. On application layer, we just...
As I have provision a nearby light server, use those serial commands:
In [1]: p = Provisioner(d[0])
In [2]: p.scan_start()
In [3]: p.provision()
How to provision...
I'm building wih Keil MDK-Lite Version 5.24.1 and I just copied the examples for gpiote into my own folder, everything was kept the same (ie copying from C:\Nordic\nRF5_SDK_14...
Hello. I tried to use UART speed 115200. But my slave does not response. I connected slave to the arduino and it is working corectly. I got 2 oscillograms . From arduino and...
Hello everyone,
Currently I'm altering the "ble_app_uart" and "ble_app_uart_c" examples (both under examples/ble_peripheral) to suit my needs. What I currently need to...
Hello,
I have interfaced one sensor with pca10040. I am using sdk 12.2.2. I am sending the data from sensor in advertisement packet(manuf specific data). Now my sensor data...
after the advertising timeout occurs the board goes into sleep mode and then immediately runs from the top of the main function. I know that a pin state change can wake up...
Edit: Rephrased the question to make it easier to answer.
I used flash storage to store a couple of variables between resets in a app made from SDK 12.2, now I am attempting...
hi,
i need to reconfigure the WDT and also change the timer value in WDT. is it possible to do that.
i tried but i can not.
1.configured wdt with timer 5sec.
2.i...
Hi guys,
we are developing firmware for nrf52832 SoC based on the mbed platform.
The firmware uses BLE and few peripherals (timers and pwms). Since our goal is to build...
