Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
My question is somehow connected to hardware side of SPI(M) peripheral implementation.
When using SPIM, I am observing 3 types of situation:
WhenSCK pin is defined...
Hello,
I took this project on about a month ago to do bug fixes within the app. The bugs are fixed but the OTA was not tested for the last 2-3 months. No changes were made...
Hi,
I am working on interfacing SD card with nrf52. I am sampling SAADC at 1000 sps and trying to write over SD card as well as sending over BLE. Both operations are working...
Hi everyone,
I am trying to update my nrf52832 chip with another MCU using UART.
I am using the bootloader example dual_bank_serial_s132 with the s132 SoftDevice.
...
I plan on using the ISP130301 and would like to ask the following:
I would like to start my schematic and layout using the ISP130310 from Insight Sip and would like...
I'm wondering if it can be work as an DFU Controller (where sends zip Distribution Packet) not as an DFU Target.
I'm trying to make Each of the NRF51 Cores to be updated...
I am using the nRF52832 very successfully for an audio application. However, I am observing an undesirable high current state after audio playback is complete.
Here is...
Hello Everyone) Have new unsolved problem. My custom PCB based on nrf52832 SoC has only controller, FXOS8700 accelerometer and MAX30205 health temperature sensor. For communication...
I have been using SDK7.2 on an nrf51822 quite succesfully for a number of projects in the past.
However, for a new project, which is just a simple beacon, no complex IO or...
Trying to keep this as short as possible. I have 3 I2C devices on a bus. A LSM303(accelerometer + magnetometer), a high precision temp sensor, tricolor LED driver TCA6057...
Hi,
I'm working on nrf51822 with soft device 130. I want to know how many packets are sending in a connection interval my min and max connection intervals are 30 and 80...
Hi,
just a simple question: I need to create an update over the air system with my nrf52 and I was wondering if transferring the new image to the chip requires especial...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
In sample project I didn't find any way to perform an update through UART like previous SDK.
Nrfutil tool documentation specify that :
Performing a Device Firmware...
Hello, per the question, how?
Is there certain register in the nrf514xx devices which can be called up in debug mode & used for such a purpose? By that I mean:
place...
