Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I'm still newbie of BLE developer, and designing a BLE device based on nrf51822 (whose service uuid is partially used for identification of serial number).
Like nordic's...
We want to design our own custom USB Dongle for connecting our sensor board to a PC. Sensor board has a nRF51 chip using Gazell protocol to transmit sensor data and also softdevice...
I am using keil compiler. The nRF51822 stack succesfuly compiled and also i am created the hex.I don't have j-link programmer but i will try to download using Ulink2 can u...
I meet a trouble like this:
My colleague used " nRF51822 QFAAC0 1322AW " to make a product. The KEIL program "based on s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK...
When nrf51822 with 32KB RAM will available? If it is going to be delayed is it possible to get samples? (I like to try IOT SDK and with my PCA10001 the heap overflows.)
...
If I don't call nrf_gzll_set_base_address_0(...) or nrf_gzll_set_base_address_1(...) what address will it use?
Also, what is the default number of send attempts?
Hi, I purchased and received the pca100028/nRF51-DK on Friday (12/19).
I've upgraded to Keil 5.12, loaded the 7.10 sdk pack, loaded the radio_test_pca100028 example ( I...
Hi
The datasheet for nRF24le1 seems to describe two ways to find out if the TX buffer is full.
Register map 07, STATUS, bit 0, TX_FULL
Register map 17...
Hi all,
I'm trying to work on my MacBook Air on BLE. I'm running Windows 7 under VirtualBox and using the new Keil µVision5.
But my problem is that whether the nRF51822...
hi all,
i have some issue about this .
when i add second vendor uuid call sd_ble_uuid_vs_add. that uuid_type.
the uuid_type always get 0x03 value.
by the BLE_UUID_TYPES...
We have some legacy code ported from other platfrom to nRF51822.
The old platform supports blocking flash write, so there will be some
readback code after flash write function...
I've had good luck running the examples such as the blinky and the basic BLE examples. Now, I'm trying to get the SPI Master example to run, but it does not seem to work out...
Hello Everyone,
As mentioned in nRF51-DK user guide, nRF51-DK has segger J-link debug out functionality. that means we can use this on board segger for downloading hex...
I have the nRF51822-DK and have been able to build and run the sample projects, e.g, ble_app_beacon.
I've just built a board using Taiyo Yuden's EYSFCNZXX module that's...
