Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Will the nrf52811 I2C compatibility work with the I2C on the MLX90614 IR sensor. I need to make sure that they will work with each other without issue. Below is the datasheet...
I have DFU OTA application running on 52840 platform on a custom board. SDK v15.3.0. I use SoftDevoce S140 v6.1.1.
Then I need to port it to 52832 platform - SoftDevice...
I have used the NRF52 before, but we got a new need for it to be used with FreeRTOS. Usually I use the RAM_START and RAM_SIZE defines the set up the ram usage for the soft...
1. I tested the following AT instruction on ncs v1.3, returned OK, but did not return the subscription message, need to modify where to return the subscription message did...
We are using I2C bus for communication with a RTC and Accelerometer. But sometimes the I2C get struck in i2c_write. It does not happens always it may happen randomly. We are...
Hi,
I just spent several hours trying to figure out why, using a nRF52 dev kit w/ SDK13 + S132 on both central/client and peripheral/server side, sd_ble_gattc_read() was...
Dear Support,
I have a question about the IPv6 networking with OpenThread. I do have an mesh network with about 50 nodes (PCA10059) and implemented CoAP servers and clients...
I just downloaded SEGGER Embedded Studio (ARM V4.52c) and plugged in my rather old PCA10040. It offered to upgrade the driver, which I accepted. Now, when I click "Connect...
Hi,
Just installed nRF Connect v3.4.1 on a macOS Catalina and get the following error message when starting any of the apps:
I've tried both reinstalling and downgrading...
Hi,
I'm making a peripheral device that needs to minimise battery usage.
My device is essentially a beacon but it allows temporary connections to send a stream of data...
Hello,
I have purchased a new nrf52832 DK board for development. I tried to run some examples like ble_app_blinky which are working properly. But when I tried examples such...
Dear All:
Our team are ready to develop a project with multicentral and multiperipheral
The project topology image lists as follow:
I want to ask how many ram it will...
I know this sounds a crazy question but is it possible to flash a custom nRF52832 board with the same firmware that is shipped with the dev kit and create a mass storage out...
Hello,
I am looking to run the ble_app_uart example from the SDK v17 in nRF only mode on the nRF52840 DK. When running the application as is on nRF only mode, it fails during...
