Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
We have a third party active power analyzer which cannot be kept in only current measuring mode. It always provide supply of 3.3 to 5V.
The DK configurations we...
Hi All,
I have up to 8 nRF52832 devices sending data back to a base unit (another nRF52832 device.) What I'm trying to do is have the remote units wakeup at a given time...
I have some questions about FSM，when I enter fsm_init() to perform fsm_any_state_find(fsm_t * p_fsm) completely in mesh_lpn_init() during debug mode by "step into"，the small...
Can you please help i use ble _ nus and after few message i need to change uart baudrate. I cloes uart then init uart with new baudrate parameter but everytime MCU goes to...
Hello Nordic team
I am working on nRF52832 dev board. SDK v-15.2.
My questions are following:
1) How much current consume if we use GPIOTE to register one pin interrupt...
Hello everyone! My team and I would like to port the SDK examples to the Arduino IDE, but we have found that the Arduino IDE does not know what board is being used. We think...
I want to use several GPIOs for different purposes.
for example, - motion detection interrupt by accelerometer - low battery alert interrupt by battery gauge.
However...
I am new to the NRF52840-DK. To burn the program into the kit, I have lots of tries to install nrfGo studio but it gives me the "no board detected readback protection" error...
Hi,
I am using my nRF52832 DK as a sniffer.
I am sniffing a BLE communication between a BLE door lock with a cellphone App.
I can see the device advertises continuously...
Hi,
I am using nRF5_SDK_15.3.0 with ble_app_uart example.When I flashed the ble_app_uart example into my nRF52840 DK it starts to advertising. If there is no connection...
Is it advisable to use coin cell battery power for nodes besides end-devices in a Thread mesh network? Where can I find technical comparison between OpenThread and BLE?
Is it allowed to use nonsymmetric capacitors to get more accurate 32k ? With 2x10pF we run some 35ppm too fast and 2x12pF the clock is 10ppm slow. We could use non standard...
Hi,
I am using SES for programming with an example of BLE Uart NUS and SAADC combined.
I can send raw data, and that all works fine, but conversion to the real ADC voltage...
Hi,
I am trying to send data from nRF52832 module to a custom application. I am receiving bluetooth characteristics but not able to get values. Value is always NULL . Can...
