Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
Hi all,
I use nRF52832 with the UART peripheral example.
I use SDK V15.0.0 and Softdevice V 6.0.0, with IAR embedded workbench version 8.22.1
Messages output with NRF_LOG_INFO...
Hi,
I am using the nRF52840, which has 256KB of RAM, (i.e. loads and load of RAM.)
I would like to allocate a buffer of 45KB.
I have tried using malloc (from the stdlib...
hello nordic! I am using NRF52832 to verify certain characteristics of BLE. the question is:After the BLE terminal device is bound to the mobile phone( Most likely Android...
I found this in the schematic and I wanted to
Confirm this is correct pinout to communicate over serial
Know where to go in the firmware to get this information?
...
Hi everyone,
I am working on nrf52832 using sdk15.0.0 using ble_app_beacon
I getting 3mA current when falling edge detected, i want to set my device as low low power consume...
Hi, Dear Nordic & All:
I use usbd_msc example to generate .xls file, and write content in it, sometimes I write successfully, and can open it right on PC with WPS，
but...
In project ,i use a TWI transaction manager to control two sensor devices.So, each device requires a GPIO to detect input interrupts. I use a GPIOTE IN event and a GPIOTE...
What is the drawback of setting the TTL on mesh packet to a high number?
I am assuming that a node will not relay the same message twice? I.e. it sees a packet for the first...
Hello!
I’m quite new to the nRF microchips and am trying to programme my nRF52-DK board following this guide ( https://infocenter.nordicsemi.com/pdf/getting_started_keil...
We are working on the OTA DFU of NRF52840. The soft device version we use is the latest: s140_nrf52_7.2.0.
Unfortunately, nrfutil does not have the code number for this...
Hello
Based on this example : https://devzone.nordicsemi.com/f/nordic-q-a/57881/store-custom-application-data-using-peer-manager?ReplyFilter=Answers&ReplySortBy=Answers&ReplySortOrder...
Hi Support,
I am observing something that is quite strange on the GPIO input. I am developing a Zigbee device with Energy harvester with NRF52840. I need to use the state...
In addition to uarts, I2cs and SPIs I tried toggling some apparently spare pins without seeing voltage changes on the pins I tried.
Which pins are available for digital...
I'm using the Nordic nRF52840-DK board to breadboard an SDHC card interface in Zephyr using SPI. I have it doing "basic" operations, but am trying to reconcile what I'm physically...
