Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Dear Sir/Madam,
I am playing with SDK12.2 on PCA10028 board and runs its HRS example. This example has a battery service and its battery level characteristic could update...
I use DFU. All ok. But I need to store my settings after update. As I was advised, I located my data from address 0x72400
But Keil added after this struc some code
...
Please Find the Attachment Screen shot of SDK Document for Advertising Module. Also Side by Side I am doing Code Walkthrough Blinky Peripheral . The Code in Blinky No Where...
Hi,
In function advertising_init(void) , I have set
and in function gap_params_init(void), I have set
still the icon doesn't change. What could be the possible reason...
Hello,
I'm trying to program my custom board with a PCA10056 following this scheme (Note that my custom board is powered by the PCA10056) :
VDD (PCA10056) ---> VTG(PCA10056...
Hi,
I'm using nRf52840 rev B and C chipset and not able to detect the NFC on the device (the rev A chipset is working). Following SW combination is used:
nRF5_SDK_15.0...
Hello,
I am working on Multi-link. I want to scan the advertising information and connect only the uuid I set up.
I want to process it on_adv_report (), but I do not know...
The output order of my scanning Saadc is not predictable.
I found two related questions, but they both are for SDK 11 and seem to have been resolved.
devzone.nordicsemi...
Hi,
Am I right that after provisioner done with network configuration all nodes save their info in persistant storage and continue work without a provisioner?
How provisioner...
HI
i'm trying to use TSL2561 sensor, but i can't geting to work. I found the code that works on the psoc that, I change it so it fits nrf52840 but it still does not work...
I want to be sure about erasing flash. Flash is divided into pages and each page has 8 blocks. The smallest amount of flash you can erase is a PAGE. Is this correct. In other...
hello,
I'm currently stuck with sd_app_evt_wait() function leaving for an unknown reason. This function is called in the main loop.
The only reasons that shall exit the...
BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part H page 2321 Figure 2.4
According to the figure, if an eavesdrop device exists in the pairing process, it is easy to obtain...
Hi support team,
I am currently working with the nRF8001 that I wanted to integrated on a my PCB.I would like to know if you have an antenna to recommend to work with the...
