Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi Nordic!
Long time short, I want to do an ANT application (S210, nRF51422) that pairs two slaves to one master. I have configured everything such that it pairs only when...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi Nordic,
We are trying to supply the chip nRF51422 with a Li-Ion battery. The nominal voltage is 3.7V, but as it is known, when full, this voltage can reach up to 4.2V...
Can the pc_ble_driver project located here be use in combination with SDK12?
We currently have it setup for SDK11 here, and want to upgrade to SDK12. We successfully built...
I want to develop a central role application (using a Redbear BLE Nano - based on nRF51)
I believe that this requires use of a softdevice and am looking for how to do this...
Hi. I am trying to set up timer in counter mode to count up signals from gpio through the ppi module, but it's not working. In main cycle I am testing the timer using led...
I want to sense bluetooth from any distance the radio can detect and without connecting, pairing or bonding. Simply turn led2 on while the nrf51822 senses RF and when it no...
For my application I need a lot of different timers. I dont use a soft device. Its a nRF52 Chip on board.
#define APP_TIMER_OP_QUEUE_SIZE 20
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Experimental Buttonless DFU worked correctly when compiled with keil, but the same example compiled in eclipse by gcc is not switching to bootloader mode. value 0x01 is updated...
Hi There,
Are timers 3 & 4 accessible to the application when using the v3.0 S132 softstack on the NRF52?
Looking at table 4 of S132_SDS_v3.0.pdf they are not listed.
Cheers...
Hi Community, many thanks for reading!
I have built a Breadboardadapter for an ISP1302
Inside
On Breadboard
There is no Groundplane or design rules.
Yes,...
I am using a nrf8001 and the arduino aci library ported to work with my project.
I have started from hello world example.
Connecting to the device from android app, sending...
Hi there.
I am compiling the Nordic MQTT subscriber example (using TLS), and see the following error:
c:\program files (x86)\gnu tools arm embedded\5.4 2016q2\arm...
I have an example app ble_app_cscs_pca10028_s110 and when I add /../../../components/drivers_nrf/nrf_soc_nosd to User Include Directories I get an error NRF_EVT_FLASH_OPERATION_SUCCESS...
