I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
For programming the nrf52832's BLE capabilities the only option that can be used is the s132 soft device right?
According to the latest specification, the maximum throughput...
Greetings,
I have an application where the DFU of a NRF52 is performed by another microcontroller via a serial port. Once the DFU is complete, the microcontroller turns...
Hi everyone!
I'm wondering about why SoftDevice stays idle (in terms of radio operation) so "long"
("t ScanReserved" = 760 us) after channel changes during scanning? Despite...
Hi,
I'm trying to do a rough calculation of current consumption for the nRF52840 chip.
The unit should sample 6 times an hour by using I2C to acquire samples from a...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Hi,
We are designed our own Beacon PCB based on nRF51822 Beacon Kit...We followed board size,PCB Antenna Trace width and GND Clearance as per Beacon kit...The difference...
As I understand it only the largest physical chip, 7x7mm nrf52840 , supports Bluetooth 5.0 long range. Is this correct?
It seems as if Nordic Semiconductor is abandoning...
Hi,
i have assigned RAM address as:
#define RAM_MEMORY_TEST_ADDRESS (0x20002BD8)
uint8_t * p_ram_test = (uint8_t *)RAM_MEMORY_TEST_ADDRESS;
to this p_ram_test i...
Hi,
In the Thread API under the Command Line Interface section, there are the following functions:
void otCliConsoleInit(otInstance *aInstance, otCliConsoleOutputCallback...
Makefile (/attachment/ca6852bdad7b5e54aaa4ce4388c4c410)Please find my code attached!!!
I have changed the makefile and the SDK config file accordingly! but the error remains...
Why can not read twi data ? at nrf52832 chip....
but Read well in Arduino....
twi interfacing with RTC DS1307....
please give me some hint.....
nrf_drv_config...
i would like to print register values of an external sensor on my screen using UART! I'm reading and writing into those registers using SPI! Printing a normal message using...
Im working on 14.0 and s132 and work inside ble_uart code...i was add rtc inside that code sucsessfully but now.. when device goes to sleep so rtc interrupt handler function...
I have just changed line 74 of nrf_drv_uart.h file as
#define UART1_ENABLED 1
instead of
#define UART1_ENABLED 0
and the example gives an error. Please find...
So i am utilizing SPI and i got it to work, however for some absurd reason after removing the segger_print statement below from before the while loop the spi would stop functioning...
