Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I developed a Nordic board with 2450AT18B100 chipset antenna. I follow the design of Solar Powered Sensor Beacon.
infocenter.nordicsemi.com/index.jsp
I test...
Hi, I'm building a product with use this kit www.nordicsemi.com/.../nRF52-DK and I would like of know how write the firmware in others CIs to can use in my circuit board....
Hello,
I am currently working on project that uses BLE peripheral and BLE central for automatic sensor calibration on custom board. There is an initial connection where...
Helllo All,
I designed on custom board (nrf51822 and used 4 programming pins(swck,swi,gnd,vcc) but how to program/flash the soc?which segger i need to purchase?
Hi There,
I am
Using Linux as host platform
I'm able to successfully compile and download the example to the nrf52dk.
But I didn't understand how to debug the example...
I'd like to get peer address after the connection between nRF52 and other 6lowpan device is established. This address will be then used to create a TCP connection with some...
Hi All,
I am using the Nordic nRF52 nrf52832 device to read a value in from an Android device. The value will be between 5 and 60 seconds. I'm using the experimental_ble_app_blinky...
I would like to change UUID programatically,initially we are trying to establish connection between phone and beacon.
We tried to change BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hello, nordic team；
I want to create a DFU for the ANR + BLE device in the nRF5_SDK_12.3.0_d7731ad \ examples \ dfu \ experimental_ant_bootloader routine.But I use this routine...
Could someone explain the difference between the following functions:
ble_conn_params_change_conn_params(ble_gap_conn_params_t *new_params)
sd_ble_gap_conn_param_update...
Hi all,
i need to have at one to one connection(one phone on one nrf52). I have created a whitelist.
What i can see is that after a pairing and a bonding, if i delete...
Hello,
I'm working on an UART application which uses experimental_bootloader_secure_serial bootloader. I've done a similar thing before with SDK-11 (though not a secure...
Hi,I use S130 V1.0 working as a master,and connect a device.My device adverting interval is 800ms， and gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//MIN_CONN_INTERVAL...
So I thought I would upgrade one of my projects to SDK13 and try out SES 3.24 at the same time. I thought I would start by getting the ble_app_uart_pca10040_s132 project to...
Hi.
I just want to upload BSP package to my NRF51 DK via mbed web app, but i can not find proper source from all the available projects in mbed. Tutorial of BSP also doesnt...
