Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I have a problem with my SPIM read buffer.
As you can see below, my SPI device received bytes correctly and answer correctly
My code is based on SPI example...
In the simple_uart.c there is a code:
void simple_uart_put(uint8_t cr)
{
NRF_UART0->TXD = (uint8_t)cr;
while (NRF_UART0->EVENTS_TXDRDY != 1)
{
// Wait for the...
Hello. I wanted to use a receiver on a quadcopter and some becons nearby(+-5 meters). Is it possible to determine the distance IN REAL TIME to the drone?
I'm a newbie to nrf52832 and would like to ask a dumb question here: can I use radio notification to implement a dynamic advertising message? I've looked into this question...
Hi,
As I know that one reading operation requires 2 connection events:
First - ATT Read Request
Second - ATT Read Response
GATT Read Message Sequence
My question...
Hello.
I'm working with the nrf52 with s132 loaded.
There is a way to have a 6Mbps on the SPI ? I try the value 0x60000000 but this do not work.
Thanks.
Eric Provost.
Hi,
there are similar questions to this but I cannot solve my problem.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC (using...
Hi everybody
Is it possible to use secure dfu (SD130v2, SDKv12.2) with 16k RAM dervices (concrete nRF51822 256k flash, 16k ram)? When I try to shrink ram in dfu project...
Hi,
i have an openwrt image running on my rpi. I made sure to build the openwrt image with 6lowpan modules and other bluez library.
i am trying to connect to the nrf52 running...
I am using Martin's code to test my I2C connection.
I use PC10040 evaluation board, SCL and SDA are 3 and 4.
My sensor is a Max 30102 pulse and HR sensor.
I used Martin...
Fight continous! I have NRF51822 chips and today i got NRF51 DK motherboard. I wanted to flash it according to tutorial found here: devzone.nordicsemi.com/.../ .
After some...
We are selling our own nRF51 and nRF52 based boards (Aistin Blue, www.iprotoxi.fi/.../iprotoxi-aistin-blue) and would like to offer customers easy way to run Nordic Semiconductor...
May I ask you a question? concerning I disable the radio of nRF51822 2.4GHZ ， don't run the Ble，don't apply the the RC Oscillator of the 16MHZ and only use GPIO，could the...
