I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
I have a few questions (using nRF51 DK and/or external nRF51822)
I use an analog pin to measure the voltage of a capacitor of an analog circuit. From time to time...
Hello,
I would like to implement HID over GATT profile (BLE) in the Beaglebone Black (BBB). The BBB will be used to interface with a laptop/computer running Windows 10...
Sorry for this long message. I am new and quite lost.
I just purchased a nRF51 DK and installed nRFGo Studio, Keil MDK and NRF51 SDK. With nRFGo, I programmed the Segger...
Hi,
I'm trying to link the static esb library (esb_gcc.a) with the mbed toolchain. Everthing seems fine until the last stage of the linking phase where my actual functions...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
I have inserted the USB dongle nRF24LU1p in to PC. In nRFgo studio, it is detected as nRF24LU1+ Bootloader. If I click on the bootloader, It shows a window from where, it...
Hi,
I've got the following error when trying to update the softdevice and bootloader on my iPad:
Error on StartDFU Message:Data Size Exceeds
I've carried out the...
Hello!
Do I need any extra passives, connecting SD card to SPIM of nRF51?
It works fine with MOSI, MISO, SCK, SEL, VCC and GND directly connected, just want to be sure it...
