I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Is it possible to communicate between 2 Nordic kits at 1 M baud without HW flow control? I came across this post in the forum which states that bytes can be missed when switching...
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
Hello,
I'm trying to create a lightbulb custom HomeKit accessory by referring to the User Guide v1.7.1. I followed the exact same steps as described in the document for...
Hi,
* (i'am using sdk14.2 ans S140 V5.0.2)
i'am trying to inegrate a beacon application to my ble_uart example , so my purpose is to advertise ibeacon pachet format only...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
Hello,
I'm using FreeRTOS on nRF51 and I would like to use task notifications instead of semaphore to simply manage task's syncronization.
To test its operation mode,...
Hi, I just copied the antenna drawing by referencing the PCA10040 v1.1 and checking the white paper (λ/4 printed monopole antenna for 2.45 GHz) .
I didn't have much knowledge...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
