When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I'm running on a nrf51822 chip, using Keil and a JLink Segger programmer. I'm running on SDK 12.2.0 and I believe I was correct in choosing pca 10028 s130 but I'm not 100...
I followed the instruction and installed the latest version of nRFgo 64bit v1.21.2. After installation, I can not find ble-sniffer___SNIFFER.zip at all.
Where can I find...
Hello,
I was able to get SEGGER_RTT_WriteString() to work correctly, however SEGGER_RTT_printf keeps giving me this issue when compiling:
._build\nrf52832_xxaa.axf:...
I am programming a beacon, first I had some problems using sd_ble_gap_adv_start() so I changed to ble_advertising_start() .
Now I have a problem when compiling:
_build...
I'm trying to use the PPK with an nRF51 dev board, and I'm getting this output whenever I try to start the PPK Software:
Checking installed packages
pyside: 1.2.4
pyqtgraph...
I tested a 23byte data transition in iPhone 5s with Softdevice 3.1.0, sdk12.2 .
it is ok. I know that iphone 5s is ble 4.0.
So I thought it would be possible on Android...
How do I set TIMER2 to interrupt every 1 ms?
Sounds like a very basic question, but I haven't succeed. For TIMER1 I can get it working, but for TIMER2 the highest frequecy...
I am using SAADC and reading in 1 analog channel. The data sheet says that scan mode is enabled when 2 or more channels are turned on. What if I am only using 1 channel ?...
Hello, after I program bootloader, sd, application, I did the following command to do read back protection,
nrfjprog --rbp ALL -f NRF51
But, even though I still can...
Is there a way to achieve what bsp_event_to_button_action_assign(button_id, action, event) does but using my own button?
The functions requires a button_id like 0,1,2,3...
When I use NRF_LOG_GETCHAR() witn nRF52 DK and onboard SEGGER UART it stops in next NRF_LOG_INFO(). Also after ARM reset it keeps in this error state. It seems that SEGGER...
Hello,
I'm trying to install wireshark sniffer on ubuntu 14.04 with PCA10031.
I follow this guide : devzone.nordicsemi.com/.../
But when I launch sudo python example_linux...
Hi,
I am trying to replicate the "Throughput and long range demo" from devzone.nordicsemi.com/.../
I have two nRF52840 boards. I am using IAR studio. I can compile,...
Hi,
i am working on TWI sensor example in SDK1. in which i connected SCL And SDA pins tonRF52 dk boards sca and scl pins. and connected voltage and ground. when i run the...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
