I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
i decided i will use a nrf52 3rd party module for my project cause i want to skip Qualification Process and Bluetooth RF-PHY test.
I haven't seen any 3rd Party...
nrf52DK - SDK12.2
This is probably a simple thing I am missing but I can't seem to find the answer.
I have been following the tutorial for BLE Characteristics ( here...
Hi,
I am working with a nrf51822 and I have seen that the way to wake up from System Off mode is by a GPIO interrupt. I wanted to know if it is needed to configure previously...
I am a new to the uVision4 and having trouble with the 51822 evaluation kit demo.
I am able to build the ble_app_hrs demo and can load and run it using the Flash / Load...
Hi
I'm using fs_storage function to read and write in flash memory. Value successfully stored in evt->store.p_data but after power off it value become 0
switch(evt-...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
Hello,
i use a nrf52 developpment board, with the SDK 12.1.0. I use the ADC example which use the ppi channel, my question is : it's possible to set the ADC driver without...
Hi all,
i try to log event in memory, and when connection is established read value from E2C and send to APP.
if i send characteristics when event BLE_GAP_EVT_CONNECTED...
I use the ble_app_proximity example of the nRF51_SDK_10.0.0_dc26b5e, the chip on my board is QFAAH00 . When I down load the code, it pops the windows "IAR Warning: Stack pointer...
I am learning BLE and trying to develop a Health Thermometer which can be seen in the nRF Toolbox
I am using Bluetooth Developer Studio but cannot get the nRF Health thermometer...
In SDK 11.0 it seems that in case pin 31 is configured as a button (using port events), nrf_gpiote_task_enable keeps triggering the port event due too a work around for OUTINIT...
I developing wearable product based on nrf52832. The product is act as a beacon and its location track by other fixed BLE readers to positioning it in particular defined area...
Hi,
I'm working on accelerometer + BLE application. My current configurations are nrf51822 and LIS3dh accelerometer chip, Protocol TWI, Softdevice 110, BLE service type...
Hi!
I'm trying to learn osTimerStart(), \ble_app_hrs_rtx.
Compiling was successful, and it is working.
If I set the timer interval shorter than 25 ms, the timer cycle becomes...
