Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello, everyone~
I used to see nRF51802 in an official document but cannot find it in the official website. Is there an nRF51802? If so, what are the differences between...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
Hello everyone.Recently I try to send some information from a "nrf51822" to phone when they are connected .So I choose "ble_app_hrs" example program,and I add two characteristics...
Hi everyone
I am working with nrf51 and I need to know how much my specific code occupies in the flash memory (I know how much is the available memory).
Thank you
I have two board - 51422AC based PCA10028 and 51822AA based custom board. Custom board doesn't have 32768 OSC.
My goal is to let custom board work with example project...
I want to use my stand alone SEGGER with nRFgo Studio. How do I do that?
It looks lite nRFgo Studio only recognises the PCA10028 board as a SEGGER but not my stand alone...
I have a ble_uart application which is working when I load it on the chip. But it will not automaticly run again if I unplug the supply and just plugin again. When I unplug...
hi,
i am using eclipse IDE to build the blinky example with soft device s130(using SDK11). i added the make file and .ld script and linked all files which is required....
Dear Nordic family,
I tried programming Raytac MDBT40 with the LED blinking code (taken from the example project of SDK 8) which worked with nRF51822 Bluetooth Low Energy...
Hi
I have been using the DFU for quite a while. I adapted the boot loader to my hardware and compiled it using Keil.
All my other code is written in another environment...
Dear Nordic Developers!
When I call the sd_power_system_off() function to put the MCU to system OFF, after that I can still see the advertiser device in MasterControlPanel...
