Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I have suspended my Beacon in SLEEP (at .5 uA) until a keypress. Is there an event that can trigger an event if there is a low voltage detection while in SLEEP?
My goal...
hello,
I am trying to write one characteristics on GATT server from a client. My server program (acts as peripheral) is working fine with MCP. But when i am trying to connect...
Hi,
I've spent the last few days trying to get this going and getting super frustrated.
After having no luck getting the nrfutil to work on Python ( another thread ...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
When exporting the example project BLE_HeartRate from the online IDE to the GCC (ARM Embedded) toolchain, the makefile fails to compile.
First, the compiler throws "fatal...
Hi:
I am using nRF51 Dongle to develop my platform, and software is base on esb_low_power_prx and esb_low_power_ptx in nRF5_SDK_V11.
For production, I need to program...
When I connect to another beacon using sd_ble_gap_connect() scanning on my device is stopped. I have to wait till connection is established or establishing connection fails...
The Nordic set comes with a Device number of it's own. I want to overwrite that device number, or store a device number in a different location in the EEPROM. Is there any...
What files within the FDS are used by the modules of the Nordic SDK?
For example, I know that the Peer Manager uses the FDS as a storage backend. I need to know what files...
Previously I implemented a DFU bootloader. It works fine on s120 softdevice.
But after I ported it to s110 v7.0 softdevice, it can not work. After investigation, I found...
Hi,
i just followed the steps for migrating to peer_manager - as lines out in the tutorial.
However i will never ever get a callback to pm_evt_handler.
I am trying...
