I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am developing some application and I have decided to use Device Addresses to distinguish between devices. I have read device addresses of 2 chips (I have read addresses...
Hi,
I am working with Gazell device and host example code from the Keil pack installer, using the default the data rate of 2MBit, so per Nordic's documentation the timeslot...
I confused that I run a SDK 9.0.0 example ble_central_and_peripheral app_s130_demo on my nrf51 SDK. then use Android App MCP to scan Advertise data. it did not work.
but...
I'm faced with a curious problem.
The examples of nRF52 SDK 0.9.2 have linker sciprt like this:
/* Linker script to configure memory regions. */
SEARCH_DIR(.)
GROUP...
Hi,
I bought two PCA10028 DK boards, try to start with the simple example with SoftDevice S110.
I download the application to the DK board by nRFgo Studio.
First...
Hello,
I bought 2 modules from this site:
www.elecfreaks.com/.../nrf24l01p-pa-lna-v31-rfm05-p-142.html
People are saying it's working great, but for me, there is something...
I had slightly modified a TWI example (using nrf_drv_twi) to work with one of my sensors; It's basically the same with a different function called to handle the received data...
I'm trying to test the throughput improvement of the S130 alpha softdevice vs S130 V1.
I notice a couple of changes in the API that I'm not sure how to handle:
First...
I've been using the ble_app_uart example with S130 on a nRF51 DK board. I wanted to add an interrupt with some GPIO pins. So I added GPIOTE interrupt handler but the compiler...
Hi all,
I want to ask you if it is possible to program nRF51822 chips (Cortex-M0) with J-Link OB assembled on nRF52 preview DK (Cortex-M4F).
I have some older boards with...
Hello,
I am working on pin interrupts and was able to handle with 1 pin interrupt. I used GPIOTE port interrupt. This is the code snippet for initialising:
NRF_GPIO...
I am trying to get my system with a hardware RTC generating periodic interrupts every 30 seconds to sleep between interrupts. I'll paste the code below, but here is the problem...
Hi,
I had an issue which the other BLE tools can connect to my BT121 module, but NCF Master Control Panel keeps looping at the connection content page. FYI, it is bonded...
