hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi everyone,
I was wondering if anyone benchmarked the time for reading a word from flash on the nRF52840. I was able to find the write/erase time on the specs document...
Hi,
We use the nrf app (Android smartphone) to establish BLE communication with trackers designed with nrf51822.
When trying to connect, sometimes it works, sometimes...
Hello， for the past I've been trying to migrate unsuccessfully my code from nrf51 to nrf52840 S140. Now that I'm unsuccessful, I'm trying to eliminate the possibility of a...
Using FreeRTOS to run nrf_cli. When Serial is not connected (as in RX,TX,GND) the board goes into a reset loop.
There are a few things that seem to help:
Don't run...
hi,
i have tried to write data into flash memory, but i can not, i can read the data from memory.
i had followed your instruction as this link
infocenter.nordicsemi...
In my project, an android phone is needed to connect to two ble devices. All my ble devices are nrf51822. The android phone can connect to and receive data from every device...
Hi,
to investigate a timing problem in my Bluetooth stack, I've hard wired the Radio ADDRESS and END events to a GPIO pin using the PPI. The ADDRESS event is used to toggle...
Hi,
I'm developing a FW with a lot of services and characteristics. Since I added the ANCS service, I have the "NRF_ERROR_NO_MEM".
Configuration : NRF51822_XXAC / S130...
hello everyone,
i use nrf51822-QFAA(256kb flash,16kb ram).i want to use sdk12.3.
at first i can't build the project,after i install some tools, i can build it ok.
...
i am using nRF5_SDK_13.0.0-1.alpha_055eef3 s132_nrf52_5.0.0-1.alpha_softdevice and used examples\dfu\bootloader_secure\pca10040\ for secure DFu OTA .everytime i try i get...
What's the current consumption for a Timer on the nRF52832 when it's used in Counter mode? Do Timers require the 16MHz or 1MHz clock when configured for counter mode?
Hi Vidar,
I am planning to start devlopment on the nRF52 and I would like to use GCC ARM with Eclipse. After having read your post "Development with GCC and Eclipse" and...
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
