The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi,
We have been using nRF52840 in QFN package in a BLE application. Due to size considerations, we want to upgrade to the WLCSP. I saw that the tuning network is different...
Hi,
We are using nRF52840 DK with 15.3 SDK (latest).
Registered at thisant and got the s340 softdevice for nRF52840 DK.
Please answer are my questions
Where...
In the Mesh SDK the scanner.c file has a power set to 0dBm:
void scanner_init(bearer_event_flag_callback_t packet_process_cb) { memset(&m_scanner, 0, sizeof(m_scanner));...
Hello,
I have nRF52832 and a smart phone with android 7.0.
I want to make a direct BLE connection between nRF and the smart phone, where nRF is a Central device (initiating...
I try to print with serial. How can I print something without a format. I want to print it directly. If yes, which function should I call?
For example, What I am looking...
I have included the reference design for the nRF52840 in my project. Unfortunately, the VIAs in Pads have a hole diameter of 0.15mm and a diameter of 0.35mm and are also still...
Hi,
I checkout v1.0.0 and try to build the at_client-sample but it fails. I cannot see anything I did wrong. I'm attaching the exact steps to reproduce the behaviour.
...
Hi nordic community
I am trying to send stop command to my device(which is connected to my NRF 52840) from my ble module(NRF 52480) after my android disconnected from the...
Hi Nordic engineer:
When I used examples\multi protocol\ble thread\ble_thread_dyn_mtd_coap_cli, I found that the device could not automatically assign LEADER, Router, and...
Hello and Thank you In Advance for Your Assistance. I have been working several days just to get a UART running for interface to a peripheral.
I am trying to connect a UART...
Hi,
As per the document(nrf91_at_commands_v0.9.1) for GPS SNR testing command "AT%XRFTEST=2,1,0" output is single integer as below .
but i am getting output like below...
We are using nRF52832 in our design. We want to collect sensor information along with time stamp. So I took nRF calendar application and tested the same. It was working fine...
I have developed an application that reads data from an analog sensor and transmits data with UART. This app is based off the SDK v14.x uart example, and SAADC example. While...
