Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
I am trying to get MCU Boot working with sysbuild using DFU with SPI external flash for FOTA over BLE with 2.9.1. I added the setting CONFIG_SPI_NOR_SFDP_DEVICETREE=y per...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Can you please help to suggest how to get hci logs in channel sounding examples? Like my use case is that I want to know which commands are going from host to controller and...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hi,
I am currently trying to build the channel_sounding_ras_initiator sample without any changes. I was successfully able to build the channel_sounding_ras_reflector.
...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Currently, we are preparing for the formal mass production of the nrf54l15, but we are encountering batch burning issues that need to be resolved urgently.
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hi All,
The nRF54l15 datasheet (v0.8) notes in section 8.25.12 under "Configuration" that UARTE20 can use dedicated pins on P2, but there is no clarification that I can...
Hello,
We recently upgraded our application to use NCS version 3.0.1 and have not been able to flash firmware onto our nRF54L15 boards. We are running into the same issue...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi,
It feels like i have a follow up question of my ticket here .
We are currently developing a product using the nrf54l15 using the nrf connect SDK v2.9.1 with the toolchain...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
