If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
Hi, I am working on eddystone project i.e nrf5-sdk-for-eddystone-master which is newly released by nordic. And I set URL,UUID and TLM frames successfully but when I trying...
Hello,
I am encountering a very strange problem with the Timeslot API.
I am developing with s130 and using the timeslot example provided by Nordic to
send data revived...
So far I've been prototyping everything on an Arduino Zero connected to a nRF24. Is switching to an nRF51822 an option for me? or will I have to switch my entire code to work...
I need to communicate with several nrf modules, 1 rx and at least 2 rx. I started with nrf24l01 but it has no rssi. For that reason i bought nrf51822.
What i have to do to...
hi,
i have doubt regarding NRF 51822BEACON KIT [pca20006 board],
......i want to configure it in all ble modes [central,periperal,broadcaster,listener],
how can i do...
Hi,
I want to add DFU OTA feature for my project, I use SDK 6.1.0 and S110 7.1.0, I found a sample Bootloader code for different version of SDK (SDK 6.0.0), from Github...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
From the SDK documentation
infocenter.nordicsemi.com/index.jsp
"...platform.h is a use case and
system specific file that can contain
defines and routines needed...
