My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
hello,
I want to change the advertise time out time by BLE_GAP_ADV_TIMEOUT_LIMITED_MAX.
Is there a problem with changing BLE_GAP_ADV_TIMEOUT_LIMITED_MAX to ex. 1000sec...
Hi,
I can use nRFgo Studio via nRF5x Bootloader to update application firmware(Hex file).
It look to be using "nrfutil.exe" to create a XXX.zip file and go through UART...
Hi.
I am on nRF52 DK (PCA10040 v0.9.0, s132 SD), SDK 0.9.2 and Linux (Ubuntu).
I am currently working on the SDK's example ble_app_uart.
I am only using gcc, and...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
Hi,
I loaded S110 v8 to nrf51. Then I loaded dfu_dual_bank_ble_s110_pca10028 bootloader.
With this setup, I'm able to download my application via the bootloader.
The...
Hi,
Reading the nRF52 product specification, I see:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to...
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive these taps as interrupt...
Hello Devzone fellows :)
As you may notice, we have posted our first webcast: Interfacing with Nordic's Softdevices .
It's the first test run in a series in which we...
Anyone knows which Nordic chips they have used in this device, and do you know if it is possible to get it to Arduinio?
www.tu.no/.../345999
http://sfty.com/#produc...
Hello,
Some little compilation errors.
in ble_radio_notification.h
typedef uint8_t nrf_radio_notification_distance_t; => is no more defined in SDK but used here
...
I need to do an hybrid app like nRF UART App but with cordova. i can connect and disconnect, but i don't know how to catch the data every time the ble send.
i'm using this...
Dear all,
I make a simple test on the UART0, putting the code in 'simple_uart.c' to my main.c. When I send out a character 'A', 0x41. From the CRO timing, it appears that...
Hi all,
I am developing ble mesh network, the source code taken from this link: github.com/.../nRF51-ble-bcast-mesh . First i tested led mesh example for two boards.
...
Hi, I need to use whitelist in ble_app_uart example, What are the steps that need to be followed for that. Is device Manager is mandatory for using whitelist. Can anyone throw...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
