I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
Can you please explain to me what bonding consists of ?
Because i want to use it in DFU from an app. I see an app where we can from the it do DFU . in Fact, the...
Hi there,
Thanks to the great tutorial from Vidar, I can play with the blinky example in Eclipse on Mac. Now I want to try the other examples, and encountered the "Error...
Dear all,
I need to know in detail the nRF51822 RF capabilities asked by bluetooth SIG.
Items 1 to 12 in chapter 1.3
See attached document RF ICS 4 1 0 (002).pdf
Thank...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
Base project: ble_app_hrs_s110_with_dfu_pca10028
Project Device: nRF51922_xxAB
Project...
Hi All,
I am trying to develop a application using radio communication, so i choosed to develop a application so it can able to tx and rx. So i integrated both rx and tx...
Hi All,
We are trying find a way to upgrade nrf51822 in the field post initial release.
I read the following posts
( devzone.nordicsemi.com/.../)
( developer.nordicsemi...
My board requires P0.9 and P0.10 to operate as GPIO pins. On the NRF52 these pins share the function with the NFC antenna. How do I make them function as GPIO pins?
I know...
Hi,
I just finished compiling my code for the nrf51 to take ADC measurements and send the hex values over ble tuart o my iphone. Now I want to see if I can send that data...
Hi, i know maybe this question was asked before, but i have a particulary issue.
I have 2 devices connected through BLE. Just when them get connected i need to send a byte...
Hello!
I need to read a string from UART, there's code below:
unsigned char GetChar(void)
{
while(!RI)
;
RI = 0;
return SBUF;
}
int Readfstr(void)
{
char...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Bootloader: dfu_dual_bank_ble_s110_pca10028 with the device set to nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
DFU Tool...
I'm trying to use BLE library for python to communicate with one Nordic nrf51844 chipset. Because one characteristic is notification enabled, I need to enable notification...
Does there exist a white paper describing some typical PPI use cases with coding examples? The only one I've found is the peripheral/gpiote example and it is severely lacking...
