Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
Hi,
Due to pcb constrain, we need to use single button mode with PG/RESET routed to SHPHLD. In this mode long press for reset in the datasheet but nothing is said about...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Currently, we are preparing for the formal mass production of the nrf54l15, but we are encountering batch burning issues that need to be resolved urgently.
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hi All,
The nRF54l15 datasheet (v0.8) notes in section 8.25.12 under "Configuration" that UARTE20 can use dedicated pins on P2, but there is no clarification that I can...
Hi,
It feels like i have a follow up question of my ticket here .
We are currently developing a product using the nrf54l15 using the nrf connect SDK v2.9.1 with the toolchain...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
