Dear Nordic Support Team,
We have a system where an MCU is connected to a Wi-Fi module operating in NCP (Network Co-Processor) mode . The MCU controls the Wi-Fi chip to...
Hi,
I have been testing out the channel sounding feature on the NRF54L15. Each device has a bias (difference between the readings and the actual distance) and I was trying...
Hi,
I am currently trying to build the channel_sounding_ras_initiator sample without any changes. I was successfully able to build the channel_sounding_ras_reflector.
...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi,
I have a device running firmware from SDK10 and using s110. I would like to update the device to use SDK11 firmware with S130v2. I'm using following code to generate...
Hello,
my application hex used to work fine before i change my bootloader and softdevice
now after falshing all the hex including the application , it is advertising as...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
In past , I was able to perform DFU-OTA over BLE transport for a custom board that has nRF51822QFAA (256kB main flash memory) SOC. I tested this functionality with Nordic...
I am trying to setup a nRF51422 Development Kit (PCA10028) v1.1.0 board with ble-sniffer_win_1.0.1 sniffer. I programmed the Dev board with firmware version ble-sniffer_nRF51822_1...
Hi all,
I am using ble_app_uart application to send data to a Bluetooth device. I am sending the data to the Tx Rx Pins of nrF51822 module via an external controller. My...
Hello forum, I've been trying to get SOME alert on my nRF51DK from a phone. I first tried the alert_notification example, but it appears that one has to write a custom Android...
I'm trying to build the blinky example in SDK 11 and load it onto a PCA10000. I'm using the make file in PCA10031/blank/armgcc and am building this under linux. If I use blinky_blank_pca10031...
Hello All,
I am using nRF51822 with SDKv10.0.0 and s110 soft device with RTX os. My project have 5 different threads with 1000 bytes of memory is needed in each thread...
Hello,
I have a project where I wish to have BLE operation while active and use RTC1 as a calendar keeper while in low power mode. So far as I have seen, the softdevice...
Hi all,
I am currently working on the nRF51422 with the S110 version of the Softdevice. The SDK version is 8.1.0.
I tried to get some information back from the Softdevice...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels. since in hardware design, I have designed the chip with...
