Can you please help to suggest how to get hci logs in channel sounding examples? Like my use case is that I want to know which commands are going from host to controller and...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
NCS -> 2.9.2 Hi, guys
This will be little bit big of a ticket.
So I recently started working with nrf9160, and I have not much dabble with M33 core as well.
But anyways...
Hi,
I have been testing out the channel sounding feature on the NRF54L15. Each device has a bias (difference between the readings and the actual distance) and I was trying...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
hi,
i want to execute a block of code in which timer should start. and stop at end of the block. and the timing depends on manual interrupt. and restart again when the execution...
Im using a board that is not one of the officially supported nRF51822 boards. Im trying to get the ANCS example project to work, but It wont broadcast or even turn on the...
hi,
i want to append data before sending. i am using ble_uart example.
here suppose the data is available on uart buffer at 1data/sec. i want to sent some timer/counter...
SDK 4.0.0-2.alpha
When run garbage collection, sometimes invalid offset on new page is present.
Adding next string fix this.
m_swap_page.write_offset = FDS_PAGE_TAG_SIZE;...
Hi everyone,
somebody recently told me that the PWM library as part of the current nRF51/5 SDK (v10 or v11) is more like a hack?
Since the docs fail to mention specifics...
I would like to know whether the amount of connections for BLE is limited by BLE spec, chip or stack (soft device)?
Also, same question regarding the possibility of the...
Hello,
I need to change my advertising Message periodically. In detail message (A) is sent in every 100ms and message (B) ist sent every 3000ms.
I defined 2 timer: ...
I noticed the nrf52-DK pca10040 comes with different ic revisions.
infocenter.nordicsemi.com/index.jsp
Where can I buy the pca10040 and be sure I got the latest in revision...
Hi!
I'm experimenting with a bare-metal implementation of SPI connectivity among two nrf51 modules. One of them is master, another is slave.
The problem is, the below...
Hi All,
In Flash read am facing one issue .
Am writing some data to Flash and trying to read back, But when I read back I get some corrupted data or am not able to read...
