I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
Hi, I would like to use RTC1-> cc[1] using app_timer drivers. How to do this? Examples show only the usage of RTC1->cc[0]. RTC1->cc[0] has been used by ble_conn_params.c and...
Hi,
After few hours my program is crashing and I'm landing on address 0x1AFF4 which belongs to softdevice. For what is responsible this code and what could be a reason...
Hi
I am using Nrf51 and Softdevice S130.I know that softdevice S130 supporting Ble 4.2.This will act as a peripheral.My mobile phone supporting only Bluetooth version 4.0...
At s120,i used the following code to send data (to s110)
if( ( wIndicationFlag_Get() == true ) && ( wConfirmFlag_Get() == true ) )
{
//APPL_LOG("Write Data\r\n");
...
Hi Nordic,
From the topic: APP_TIMER_TICKS value , I've know how to use it, but is it possible to use different prescaler value in the same code?
For example the nRF5_SDK_12...
Hi, I need help for generating the init packet. I'm using SDK 11.0.0 , s130 on nrf51822. To build bootloader, I've used the sample bootloader with some include path changes...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
As title,
I found that on the official website,
and I think it's extremely useful for someone(me) who need to measure the power consumption(current).
I can't find...
