Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am working on a system where two nRF51 will communicate with use of the ANT protocol (S210). The master and slave must be paired after pressing a button on both sides. I...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I want to power the dongle from a 5V battery but don't want to solder directly to USB pads at the risk of ruining them. Can I put the 5V from the battery at the Vin point...
I have S110 peripheral device with custom UUID, created as described in www.nordicsemi.com/.../80193304 .
On the other side i have S130 device who successfuly scans and connects...
Sorry for the non-tech. question but I just heard that BlueTooth group is significantly changing BLE licensing policy. Maybe it's some kind of FUD but it should be mandatory...
Hello,
I am running the s110_nrf51822_7.0.0_softdevice.hex and am encountering an nrf callback assert on line 1377 of rem.c.
Without any visibility into this code I...
Hello, before you say anything: "yes I have searched!" :D
I found that this question was similar to mine
How to write GPIOTE Interrupt
Now I am fairly certain that I...
Hello,
I am trying to connect to one specific device. To make this I am advertising with the whitelist. The problem is that the whitelist do not seem to work. I got the...
I am using the nRF51822 module. I am using the following code to set my device discoverable:
ble_gap_adv_params_t adv_params;
ble_gap_addr_t *whitelist_addr[1];
...
I've got a custom board with an nrf51822 (ic rev 2, QFAA), and I'm trying to understand some unexpected current draw that I'm seeing from the board. Currently the entire custom...
Hey there,
Red Bear Labs sells a board with a NRF51822 Module on it. From a past post I have found it is said:
"embedXcode supports the nRF51822 MDK board for both the...
I am playing with S130 to behave as a peripheral device and a central observer. This is working great.
I am new to the central side of things and have a quick question...
