I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
To support a mix of v2 and v3 chips, I want to use the 7.x SDK. But I'm not sure it's compatible. The matrix at infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
I'm trying to use the nRF52 preview DK from Linux. Could anyone provide the correct JLink commands for flashing both a standalone hex, as well as one with a softdevice?
...
I'm writing a build script for gcc for the nRF51 and I want to use the provided .ld scripts.
In SDK 8, those scripts were renamed from gcc_nrf51_XXX_xxab.ld to nrf51_xxab...
Hi,
I want read accel data from BNO055 sensor to NRF51 DK board, but SCL and SDA pins are 1 always.
My code is the next one:
#include "twi_master.h"
#include "twi_master_config...
I have existing design with I2C accelerometer on P0.1 and P0.2 (SDA/SCL). Don't need extreme data rates. Since examples of initializing on-board TWI don't seem to exist, and...
I am developing a tool that will be using the existing NRF51 dongle to run the S130 SD and it is being written in Python. There is no way to change any of these parameters...
Does anybody have a suggestion for a relatively low cost way to test the output power of a nRF24L01+ module? We make the modules (which are identical to the demo module) in...
Hi,
I am using the GPIOTE->PORT event to detect button presses and I would like to detect both button press and button release.
However, it seems like SENSE can only...
(this is duplicate with a support case I just opened... I hope that's okay.)
Hello, I am setting up a new laptop (our development machine caught a virus) and have installed...
Hi,
I have a sensor which sends data in a not specific time and each time start to sending data sends more that 100 data in 5 seconds
My problem is i just want one data...
Hello,
as described in the Compatibility Matrix it is necessary to use a revison 3 chip to use the S130 SoftDevice? Right?
Please explain why the Revision 2 chips...
I'm working in a project & I want to wake up the system from the sleep mode but it didn't wake up or I don't know what is expected on the wake up, will the system be run from...
Hello
I am using PCA10028 and I have written some customized service after taking help form nAn36 documents. Now I want to combine the predefined standard services like IMMEDIATE...
Now that the infocenter is available, please consider making product anomaly descriptions available at a permanent URL, e.g. infocenter.nordicsemi.com/.../PAN .
The frameworks...
Hi,
Same question in the ARM forum: topic
I am a (French, sorry for my English) software engineer with very little knowledge in hardware. As part of a prototype, I'd...
