hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
In porting from SDK6 to SDK9, it looks as though
nrf_gpiote_task_config()
has been replaced with
nrf_gpiote_task_configure()
What, if anything, has replaced
nrf_gpiote_unconfig...
I'm using sd_ble_gap_address_set() to randomize mac address and it's working fine. But I'm confused about how to change it back to normal(initial value I see) once I wan't...
i cant find lbs example on \SDK8.0.0\examples\ble_peripheral\nrf51-ble-app-lbs-master\arm and compile.I planned to work with nrf51822 dk. The given example in github shows...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
Sorry but I've been stuck on this for a few days now and I have to give up and ask for help.
I'm attempting to set LED0 when BUTTON_0 is pressed and LED1 when BUTTON_1...
Hello all,
I am working on a device (nrf51 and s110) which is going to communicate with multiple centrals (smart phones).
The device uses a whitelist to connect to only...
Hi,
I run a custom board with an nrf51822.
If I program the device in the IAR IDE everything works fine but I cannot program the generated hexfile with nRFgo Studio or...
Is it 'NRF_RADIO->TASKS_DISABLE' or 'NRF_RADIO->TASKS_DISABLE = 1'?
Restarting advertisements seems not to be affected and I guess 'cancels out' NRF_RADIO->TASKS_DISABLE...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
