I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
I have two UART devices on a custom board with an nRF51822. I've just upgraded the SDK I use from 8.1.0 to 10.0.0 and one of the UART connections has stopped working, but...
Totally get the limitation of 3 PWM channels.
Wondering if I can dynamically re-assign which 3 pins are tied to the PWM outputs.
At boot time, I call this function:...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I have got reliable writes working on nordic side (nrf51822 eval board).
Tested them with master emulator dongle by using write long button on MCP on PC.
I...
Hi, I'm porting my project from SDK8.1 to SDK10 and got a problem in app_timer.c
Main chip :nRF51822 QFACA1
Crystal:32Mhz, no 32.768
Initial is fine.
APP_TIMER_INIT...
Hi, I realize that the compatability matrix states that SDKs 7 8 and 9 are built for rev3 of the nrf51822 and nrf51422. It has been mentioned however that they may still work...
The S130 SD supports up to 3 concurrent central connections. Once it has made the maximum number of connections can it still scan for non-connecting peripherals, e.g. to look...
I have 2 PWMs working with the version 8 softdevice on an nRF51422, and it's straightforward enough to change the duty cycle with app_pwm_channel_duty_set() in the app_pwm...
The way of entering the bootloader mode is sending the command,then run the code as follows:
void jump_to_bootloader(void)
{
uint8_t softdevice_enabled;
uint32_t err_code;...
I'm sorry but i don't know where else to turn. The tutorial on adding a characteristic to a service (the nordic tutorial i am basing this off) isn't finished and I have no...
Hi
I did not quit yet understand the Gazell Pairing library.
If an encrypted message is send, how do I add some payload to the acknowledgement.
And how will I be able...
Hi,when i set NRF_RADIO->MODE in RADIO_MODE_MODE_Nrf_1Mbit ,then use radio_tx_carrier(txpower_, mode_, CH_LOW); i got a picture with spectrum analyzer like this ! , when i...
Hi
I have been using the double buffer DFU for a while now, and it works reliably for me.
However, I am hitting the application size limit that can be handled by the double...
