I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
From what I can see so far, it appears that the application processor flash is at 0x00000000 - 0x00100000 and the network processor resides at 0x01000000 - 0x01040000 .
...
I am having trouble because TX / RX processing using UARTE cannot be performed.
nrf52840 DK <---------> PC
The operation of TX / RX can be confirmed with UART. (Interrupts...
Hi,
I have two questions:
1) After requesting PSM mode (assuming the MNO supports PSM mode for NB-IoT) and afterwards enabling GPS, does the GPS automatically detects...
Hi,
I am currently working on the development of a customized Tracker application. I was testing one use case where the Tracker definitely not being able to achieve a GPS...
Hello,
I'm using BT840XE module and ATT_MTU Throughput Example with S140. My goal is to measure maximum data transfer speed between module and different phones. Module acts...
Hi,
I'm using nrf52832 (SDK 15.3). And I have 24 chips on the same I2C bus. They all work fine right row. But if one of the chip is broken, the whole system will crash....
If a reliable mesh transfer is ongoing the node will crash with a mesh assert at access_reliable.c:373, in access_reliable_cancel_all().
This happens because access_clear...
Hi all,
I am looking for the Objective Product Specification for the nRF52840 chip. I have only found the Objective P roduct Specification for nRF52832 in version 0.6.3...
After setting up my Peripheral Mode I am also looking at ways to improve my current design. I would like to ask about Mesh support on the NRF Thingy 91 integrated with the...
Was anybody able to connect to HTS (Health Thermometer Service) on iOS applications, OTHER than nRFToolbox or LightBlue? Which applications did you use?
I tried a dozen...
Greetings....
It is great that you provided SDK UART coexistence example for nRF5 SDK for Mesh v3.1.0 and nRF5 SDK v15.2.0 release for Client node with nRF52832 DK. However...
I am trying to build an example code for PCA10040, but I always have a lot of compiler error: C:/Program Files (x86)/SEGGER/SEGGER Embedded Studio for RISC-V 4.42/source/thumb_crt0...
Hello,
I'm working with the Nrf52832 Dev Kit and the ble_uart_example. After flashing with the hex file and powering the Dev Kit, the on-board-LED starts to blink. Now I...
Hi Nordic team,
I am currently developing a concurrent wireless application with BLE and a proprietary protocol using the timeslot API.
My setup:
nRf52840 DK
SDK...
Hello, guys!
We are working with SDK 15.0.0 and nRF52840 SoCs.
There is a need to transfer a few MBytes of data from the PC to nRF52840 and then on external flash memory...
