Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
I just downloaded their iccv8cortex trial version and it includes the 51822 as a target. My 5 minute test drive not withstanding, it looks like this might be a good option...
How to reduce power, for bond connections such as cscs services which only requires communication once per second?
Is there a way to manually / automagically turn off the...
Before I call sd_power_system_off(), I do the following:
NRF_TWI0->ENABLE = 0;
NRF_TWI1->ENABLE = 0;
NRF_ADC->ENABLE = 0;
NRF_SPI0->ENABLE = 0;
NRF_UART0->ENABLE =...
Hi
I using nRF51822 ble_app_uart project with softdevice 7.0.
I need to manage my internal flash memory map so i cannot use pstorage libary test main.txt .
So i try...
Hi,
What is the typical range of operation that can be achieved by nRF51822 Bluetooth Smart Beacon Kit ? I know it depends on the Tx power, but can a range of approx 30ms...
I need help choosing between 2 technologies above, my goal is to enable multiple (up to 20) devices exchange small amount of information (around 30 bytes) between each other...
Hello
How many packets can the nRF8001 send in a single connection event? I have seen here, that it is possible to send up to 6 packets with the nRF51822 + Softdevice S110...
Hi, we've been using nRF51822 for developing application and iOS 7.x detect then just fine.
Since I upgraded to iOS 8. Beacons are 'invisible' to our application.
I was...
When I try to use the mergehex tool to combine all three my application never seems to get properly combined.
What I'm doing:
mergehex -m softdevice.hex myapp.hex -o...
