I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
I've run ble-sniffer_win_1.0.1_1111_Sniffer.exe and pressed CTRL-R, then I get:
Keyboard input error: [Error 2] The system cannot find the file specified..
The log file...
Hello
I am developing an application where the data troughput is very important.
As i understand, the data thoughput is dependent on the connection interval and the number...
Dear developers,
I have a problem with peer manager reporting PM_EVT_ERROR_UNEXPECTED right after it has reported PM_EVT_CONN_SEC_SUCCEEDED.
This is quite a long call...
We all know that PPI can have the same event to trigger other tasks.
But I couldn't find any official document explaining the priorities/timing of those tasks linked to the...
Hi
I am trying to put the nrf52 device to system off state, in order to get minimal current consumption.
When I don't use the soft device, and enter system off state by...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
If i scan again when it is scanning, system goes halt and reset.
So i want to check it's scanning or not before I make it scan...
We have an RFID application, the tag sends the 10 byte data and the data is read at the Receiver continuously thorough SPI channel to MCU.
Payload of 10 bytes, Enable CRC...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello, I want to detect the any activity of the ADXL 362 and blink the LED ON and it should also detect the inactivity to turn OFF the LED.I am able to generate the activity...
Hi,
We are using the Nordic Semi nRF51822-QFAA-T to do BLE project, but when we test CE/FCC RF test(Conducted / Radiated), there has a lot of noise around 2.4G.
BTW...
Hello,
I try to find the information if there is a softdevice (for nrf51 or nrf52) that supports "LE Secure Connection".
In general, where can I find which bluetooth version...
I'm lost.
Can someone point me to place or the best example of how to send data (any) from NRF51882 to iOS app when app is in background.
Is it possible at all ?
I'm trying out the ble_app_gls demo with the Nordic Master Control Panel app (on Android). What I see is that the MCP can connect to the device without bringing up a pairing...
Hello,
We are working on a third party module from china. We are trying to program it with keil but we are having problem with configuration.
We are using S130 v1 and...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
