Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
I develop my BLE with SDK 8.1 and softdevice 8.0, and I want to restore some data(about 50 bytes) to flash, can anyone please help to provide me an example for the entire...
I have had a look at you experimental implementation of DFU signing.
I'm very concerned about the code size. The old Bootloader used about 13KB and the new one with signing...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
I've got 4 services with 15 characteristics between them. Trying to add any more than that results in sd_ble_gatts_characteristic_add() returning NRF_ERROR_NO_MEM .
All...
Hi Expert,
I found a weird case that at my 51822 plaform with s110 enabled, if I define a global buffer like:
static uint8_t system_buffer[1024];
it obviously will...
Hi
The nRF24Le1 has 256 bytes in the infoPage for user data, starting 0x0100.
My question is how to write to that area?
Is it accessible from nRFgo Studio?
Is it accessible...
Hi every body,
Is there any way to increase the support packet per connection to more than 1 packet for S120 softdevice if i have just single slave and single master? ...
HI,
I have followed all the steps from devzone.nordicsemi.com/.../ and I can relay text between Termite & my iphone.
Can someone share a function / method which I can...
Hi,
I used the ancs demo of nRF51_SDK_7.2.0_cf547b5 to modify our application. It still work well, but sometime when I left the device and went out with my Iphone about several...
Hi,
I have two customs boards and on the one with the QFABA0 I can go to system off and see 0.6uA of consunption but on another board with the QFABB0 I go into system off...
Hello,The user manual describe that the NRF51822 can commuiate with NRF24L01.but,when I debug this system,There is something wrong with Address and data.I try to translate...
Hi BLE fellows,
Following the steps explained here , I have tried to integrate the OTA DFU feature & bootloader from the latest SDK to my application and tested it on my...
