Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I want to run the Direct Test Mode for nRF51422 on my board, I'm trying to use the nRFgo Studio.
When I'm trying to connect to the specific COM port, I get the following...
Custom Board which has NordicSemi nRF51822-QFAA MCU,
a temperature sensor (Si7020-A10), and a white LED. The circuit follows the internal LDO setup.
(Ref. nRF51822_PS...
Hello,
i use Bootloader from SDK 7.2.0. I have some questions about init packet handling:
The bootloader compare the device type, device revision and softdevices...
During ble ADV，my device will consume 60uA，when ADV stoped it will drop to 13uA. But when I get ble connected current will up to 130uA.
I test nrf51_sdk_v6_1_0_b2ec2e6...
Hi,
in the new version of S110 (8.0.0) I can see the implementation of scan services:
SD_BLE_GAP_SCAN_STOP, /**< Stop Scanning. */
SD_BLE_GAP_CONNECT, /**< Connect....
Hi,
like many others, I'm confused with Peripheral Passkey Connection.
I'm playing with the ble_app_hrs, in order to be able to setup a Connection Passkey (for the moment...
Just got the S110 SD spec, version 2.0. Very interesting.But I've recently switched from projects on the Keil MDK IDE to the mbed environment (using the nRF5-DK as test platform...
Hi All,
Has anyone mimicked the nrf8001 ACI interface over SPI on the nrf51x22 devices using S110 soft device?
I am interested in increasing throughput by using 6 packets...
Hello,
I am working on a project regarding the pairing security of two BLE devices. nRF8001 chip follows the v4.0 specifications which lacks security against passive eavesdroppers...
I require access to SDK 4.2.2 and can't find the download link on "my pages". The link must have been removed.
I only see links for SDK 5.2 onwards.
Could someone from...
can you tell me that whether raspberry pi can be used as a beacon(i.e. for scanning) ) by using USB dongle 4.0 and nrf8002 be used as transmitter in localization systems?
Hi guys,
I design one custom application based on the ble_app_uart demo and find the device is advertising when power on. I want to set it auto connect once the device has...
Background :
I'm working with an nRF51822-EK development board. We're working on a project implementing the S110 soft device. We need to create a minimalist Bootloader...
I try to follow
devzone.nordicsemi.com/.../
but on the paragraph Using the nRF51 Dongle
I always receive "No response from master emulator "
also after flash the board...
