why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I'm testing my nRF51822 Bluetooth Smart Beacon Kit (pca20006). I've successfully uploaded ble_app_beacon_bcs code example to my beacon via Master Control Panel Android app...
hardware:pca1001
software:s120 v2.0.0
sdk 6.1.0
i will get rssi value by connected by s120.so i update the s120 to v2.0.0. but when the app run,
an error occur.[APPL...
Hi All,
I tried to use the nRF51422 device UART RXTO events using nrf51 SDK v6.1.
I set the NRF_UART0->INTENSET in app_uart_init() as following:
// Enable UART interrupt...
Hi, I have just managed to successfully read ADC values and send as a service but they are in uint8 format. Is there an easy way to convert this to decimal within my adc handler...
Is there provision for a serialization application processor to control GPIO on a nRF51822 used in serial connectivity mode? Can the nRF51822 be used as an I/O expander?
Hi,
I want to simultaneously read the value from 3 analog pins. For this, do I create just one adc_init function and handler functions or do I need to create multiple initializing...
Connections to my peripheral device are generally very short. I don't really need to have my device request a connection parameters update.
Does this mean that I can safely...
I purchased a pair of FTDI cables, and I can't seem to get them to work.
Unsure if the pinout is standard but here is the mapping of the cables provided:
Red wire： 5V...
I am using the N548 with the S310 soft device. I have set up the device for asynchronous communication via the UART. I can send ANT+ commands via the UART and I get valid...
Hi there,
I am quite new to BLE.
I am about to buy a nRF51822 Bluetooth Smart Beacon Kit. But before that I would like to be sure if I am able to advertise battery level...
Hi,
We just recently received our (custom) board with the nrf51822.
To program and debug the nRF I use the pca10028 and the debug out header.
I wrote a very basic program...
I tried loading SoftDevice, Bootloader, and Application using the SoftDevice and Precompiled hex files that come from the example code version v1.1.0. I am using nRFgo Studio...
While attempting to update the firmware from a HEX file, the DFU Application in the nRF Toolkit reports that the upload failed with an unknown error 22. I was sniffing the...
I have a bootloader running on my NRF51822. It uses a relocated vector map in RAM and jumps to function.
I therefore have two debug files and source code sets.
Does...
I am using nRF51 SDK with version 7.2.0, s110_nRF51822 with version 7.1 and gcc_arm and connect the pca10031 board via JLink and try to load bin files but it returns error...
