Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I am using 52840 dongle, program using this: nrfjprog --reset --program _build/nrf52840_xxaa.hex --family NRF52 --sectoranduicrerase, but I got There is no debugger connected...
In the SDK example, it says:
Connect to the device from nRF Connect for Desktop (the device is advertising as 'Nordic_HRM'), then bond to the device.
However, I couldn...
Hi,
After trying to flush a program to the dongle with no success, the dongle got into a state where it's not recognize by windows and no LED flashes on it when plugged...
Is there a way to get “Help”/documentation on nRF SDK functions inside Segger Embedded Studio the same way it does it with standard C functions when you click on a function...
Hi
I used nrf_sniffer_v2.0.1 and wireshark3.1.1 to capture 113 bytes package send by nrf52832
but the package was divided into 5 packages in wireshark while use app receive...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) Instead of UART, I am trying to enable...
I stumbled upon an issue where the LFCLKSTAT register in the NRF_CLOCK peripheral can not be properly evaluated after a softreset if the application that was running before...
Hello guys,
I'm pretty new about embedded development. I want to transfer data by BLE (probably UART?) and then read from COM port of my win10 laptop. Can you give me a...
Hello!
I compare the timer every 1ms and process it. In order to check whether it can be executed every 1ms, I am going to refer to the register value by "TASKS_CAPTURE...
I would like to use Gazell along with BLE using the TimeSlot API. As part of this I need to set the Gazell mode to NRF_GZLL_MODE_SUSPEND while waiting for the next timeslot...
Hello.
I am trying to build project for thingy52 but since latest release of sdk for thingy does not work well with SES -> https://devzone.nordicsemi.com/f/nordic-q-a/27311...
I am trying to interface BMI160 Shuttle Board to the nRF52840 Development Kit using TWI interface. I am using IAR Systems IDE and have modified the "twi_sensor" Example code...
Hi,
I am using ncs V1.0.0
When I configure P0.5 as input it takes 37uA current. (Interface with PCA63548 / LIS2DH Interrupt)
If I not configure the pin as input getting...
Hello .
We have an issue with the SPI channel.
We found out that when our GPIO config as SPI the CS drawn a lot of current when it connect to the slave device device AD7770...
